USB-Interface 2 / 3 Firmware
Filename: USB-Int2_standard_1_1.enc, USB-Int3_standard_1_1.enc
Author: MFTech
Version: 1.1, enhanced Vista compatibility
Release Date: 23 Jan 2007
Version: 1.2, mixer added
Release Date: 30 Jan 2007
Required USB-Interface: USB-Interface 2 / 3
Required USB-Interface Software: HID-Bootloader
Required IntCon Version: 2.0 or above
Description/ Beschreibung
[color=blue]It increases Windows Vista compatibility.[/color]
Die Firmware erhöht die Kompatibilität mit Windows Vista.
Restrictions/ Einschränkungen
-
Installation
[color=blue]- Switch on Bootloader Function
- Save changes in the USB-Interface
- Do the firmware update: Erase - Open - Program - Verify[/color]
- Bootloader Funktion einschalten
- Änderungen im USB-Interface speichern
- Firmwareupdate durchführen: Erase - Open - Program - Verify
[color=blue]!!! WARNING !!!
PREVIOUS FIRMWARE WILL BE OVERWRITTEN BY FIRMWARE UPDATE. THE INTERFACE CAN GET DAMAGED DURING THE UPDATE. THE UPDATE IS COMPLETELY AT YOUR OWN RISK.[/color]
!!! WARNUNG !!!
DIE VORHANDEN FIRMWARE WIRD BEIM UPDATE ÜBERSCHRIEBEN. DAS INTERFACE KANN DURCH DAS UPDATE BESCHÄDIGT WERDEN. DAS UPDATE GESCHIEHT AUF EIGENE GEFAHR.
Firmware http://www.mftech.de/cgi-bin/versioncheck.pl
Forum-Archiv
Firmware Update USB-Interface 2 / 3 für Windows Vista
10 Beiträge · zuletzt aktiv 06.10.2008, 16:24
Nur Lesezugriff. Antworten, Anmeldung und private Nachrichten sind deaktiviert.
This is a bad firmware!!
It don't work.
I flash the usb interface II and he hang.
What now?
It don't work.
I flash the usb interface II and he hang.
What now?
If your Interface got damaged during the update process, you can return it and the firmware will be installed correctly.
How?? The program is closed because the program crashed and I say: don't send the error to microsoft.
Return the Interface to the postal address under the web page Contact.
Oke. Is it free and can you flash the vista fw for me?
It's free. However, you have to pay the postage there and back.
Thanks for your answer! I send him back.
I came across the Vista incompatibility issue as described.
Since the Interface is not recognized on my Vista PC, it's impossible to upgrade the firmware.
So I've tried to use another PC running XP. Installed the Multiplex driver, then IntCon following the instructions. So far so good.
The interface is recognized.
I launch IntCon and select the MFTech device. Then activate the bootloader and save it to the interface.
So far so good...
But here starts the problem. After I exit the IntCon application, I disconnect the interface, wait a couple of seconds and reconnect.
Launch the IntCon again and there's no sign of a bootloader device. I do have the MFTech device tough.
When I try to change the firmware, the popup appears but waits for the bootloader.
Any idea what I can do to solve this?
The interface seems to work fine when I connect my transmitter.
Since the Interface is not recognized on my Vista PC, it's impossible to upgrade the firmware.
So I've tried to use another PC running XP. Installed the Multiplex driver, then IntCon following the instructions. So far so good.
The interface is recognized.
I launch IntCon and select the MFTech device. Then activate the bootloader and save it to the interface.
So far so good...
But here starts the problem. After I exit the IntCon application, I disconnect the interface, wait a couple of seconds and reconnect.
Launch the IntCon again and there's no sign of a bootloader device. I do have the MFTech device tough.
When I try to change the firmware, the popup appears but waits for the bootloader.
Any idea what I can do to solve this?
The interface seems to work fine when I connect my transmitter.
If your device is too old it does not have a bootloader. If you cannot remap the channels in IntCon, your device is too old. However, you can exchange your device with a new one (ask support via email).